obniz Parts Library

MQ9

GitHub
MQ9
Usable Devices :
obniz_board
Found at :
秋月電子通商
www.aliexpress.com

MQ9

High sensitve multiple gas sensor especially for carbon monoxide and CH4,LPG.

If you are using just MQ9(not module), Then prepare load resistance around 2k ohm.

This sensor need pre-heating. To get stable output, wait for heat-up, minimum 2 minutes.

This library get analog voltage from a sensor. Output voltage will increase regarding gas level. When you need actual level (ppm), you should do calibrate the sensor and prepare a formula.

wired(obniz, { vcc, gnd, do, ao});

name type required default description
vcc number(obniz Board io) no   VCC or H on MQ9.
gnd number(obniz Board io) no   GND or H on MQ9.
do number(obniz Board io) no   digital out
ao number(obniz Board io) no   analog out
// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.onchangeanalog = function(voltage) {
  console.log(voltage);
}

startHeating()

It start heating.

// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
mq9.startHeating();

[await] heatWait(sec: number)

It start heating and wait for a while.
You can update wait time.

name type required default description
sec number no 120 seconds for wait
// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.onchangeanalog = function(voltage) {
  console.log(voltage);
}

onchangeanalog = function(voltage: number)

Specified function will be called every voltage change.

// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.onchangeanalog = function(voltage) {
  console.log(voltage);
}

onexceedvoltage = function(voltage: number)

Specified function will be called only when a voltage exceed voltageLimit variable.

// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.voltageLimit = 1.0
mq9.onexceedvoltage = function(voltage) {
  console.log(voltage);
}

voltageLimit = number

It define the level of onexceedvoltage call.

// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.voltageLimit = 1.0
mq9.onexceedvoltage = function(voltage) {
  console.log(voltage);
}

onchangedigital = function(voltage: number)

This function only be called when do was specified at wired function.
do output high/low regarding output. It compared in a module.
This function will be called every change of do.

// Javascript Example
var mq9 = obniz.wired("MQ9", {vcc:3, gnd:2, do:1, ao:0});
await mq9.heatWait();
mq9.onchangedigital = function(value) {
  console.log(value);
}

Supported from: obniz.js 3.5.0